Tugas Pertemuan 5

3.3.2.2 Packet Tracer – Configuring Rapid PVST 

Part 1: Configure VLANs

 

Step 1: Enable the user ports on S2 in access mode.

S2(config)# interface range f0/6,f0/11,f0/18

S2(config-if-range)# switchport mode access

S2(config-fi-range)# no shutdown

 

Step 2: Create VLANs.

S1(config)# vlan 10

S1(config-vlan)# vlan 20

S1(config-vlan)# vlan 30

S1(config-vlan)# vlan 40

S1(config-vlan)# vlan 50

S1(config-vlan)# vlan 60

S1(config-vlan)# vlan 70

S1(config-vlan)# vlan 80

S1(config-vlan)# vlan 99

 

S2(config)# vlan 10

S2(config-vlan)# vlan 20

S2(config-vlan)# vlan 30

S2(config-vlan)# vlan 40

S2(config-vlan)# vlan 50

S2(config-vlan)# vlan 60

S2(config-vlan)# vlan 70

S2(config-vlan)# vlan 80

S2(config-vlan)# vlan 99

 

S3(config)# vlan 10

S3(config-vlan)# vlan 20

S3(config-vlan)# vlan 30

S3(config-vlan)# vlan 40

S3(config-vlan)# vlan 50

S3(config-vlan)# vlan 60

S3(config-vlan)# vlan 70

S3(config-vlan)# vlan 80

S3(config-vlan)# vlan 99

 

Step 3: Assign VLANs to switch ports.

S2(config)# interface f0/6

S2(config-if)# switchport access vlan 30

S2(config-if)# interface f0/11

S2(config-if)# switchport access vlan 10

S2(config-if)# interface f0/18

S2(config-if)# switchport access vlan 20

 

Step 5: Assign the trunks to native VLAN 99

S1(config)# interface range f0/1-4

S1(config-if-range)# switchport mode trunk

S1(config-if-range)# switchport trunk native vlan 99

 

S2(config)# interface range f0/1-4

S2(config-if-range)# switchport mode trunk

S2(config-if-range)# switchport trunk native vlan 99

 

S3(config)# interface range f0/1-4

S3(config-if-range)# switchport mode trunk

S3(config-if-range)# switchport trunk native vlan 99

 

Step 6: Configure the management interface on all three switches with an address.

 

S1(config)# interface vlan99

S1(config-if)# ip address 172.17.99.11 255.255.255.0

 

S2(config)# interface vlan99

S2(config-if)# ip address 172.17.99.12 255.255.255.0

 

S3(config)# interface vlan99

S3(config-if)# ip address 172.17.99.13 255.255.255.0

 

 

Part 2: Configure Rapid Spanning Tree PVST+ Load Balancing

 

Step 1: Configure STP mode.

S1(config)# spanning-tree mode rapid-pvst

S2(config)# spanning-tree mode rapid-pvst

S3(config)# spanning-tree mode rapid-pvst

 

Step 2: Configure Rapid Spanning Tree PVST+ load balancing.

S1(config)# spanning-tree vlan 1,10,30,50,70 root primary

S2(config)# spanning-tree vlan 1,10,20,30,40,50,60,70,80,99 root secondary

S3(config)# spanning-tree vlan 20,40,60,80,99 root primary

 

Part 3: Configure PortFast and BPDU Guard

 

Step 1: Configuring PortFast on S2.

S2(config)# interface range f0/6 , f0/11 , f0/18

S2(config-if-range)# spanning-tree portfast

 

Step 2: Configuring BPDU Guard on S2.

S2(config)# interface range f0/6 , f0/11 , f0/18

S2(config-if-range)# spanning-tree bpduguard enable

 

Step 3: Verify your configuration.

 

 

 

 

 

 

 

 

 

 

 

 

Tugas Pertemuan 3

 

1. Setting IP Configuration pada PC 1 dan 2

 PC 1

IP Address : 172.17.0.21
Subnet Mask : 255.255.255.0
Default Gateway : 172.17.0.1

PC 2

IP Address : 172.17.30.23
Subnet Mask : 255.255.255.0
Default Gateway : 172.17.30.1

 

2. Lalu Klik pada Router dan buka tampilan CLI ketik perintah berikut :

 

 

 

Router>en
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface fastEthernet 0/0
Router(config-if)#ip address 172.17.0.1 255.255.255.0
Router(config-if)#no shut

 

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
 
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
 
Router(config-if)#ex
Router(config)#interface fastEthernet 0/1
Router(config-if)#ip address 172.17.30.1 255.255.255.0
Router(config-if)#no shut
 
Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up
 
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
 
Router(config-if)#ex
Router(config)#ex
Router#
%SYS-5-CONFIG_I: Configured from console by console
 
Router#

 

3. Buat VLAN 10 dan 30 pada switch dengan menggunakan perintah :

 

 

Switch>en
Switch#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#vlan 10
Switch(config-vlan)#name A
Switch(config-vlan)#vlan 30
Switch(config-vlan)#name B
Switch(config-vlan)#exit
Switch(config)#interface range fastEthernet 0/1, fastEthernet 0/11
Switch(config-if-range)#switchport mode access
Switch(config-if-range)#switchport access vlan 10
Switch(config-if-range)#ex
Switch(config)#
Switch(config)#interface range fastEthernet 0/2, fastEthernet 0/6
Switch(config-if-range)#switchport mode access
Switch(config-if-range)#switchport access vlan 30
Switch(config-if-range)#ex
Switch(config)#ex
Switch#
%SYS-5-CONFIG_I: Configured from console by console
 
Switch#

 

4. Ping ke pc 1 dan 2

 

 

 

 

Packet Tracer PC Command Line 1.0
C:\>ping 172.17.0.21
 
Pinging 172.17.0.21 with 32 bytes of data:
 
Reply from 172.17.0.21: bytes=32 time=3ms TTL=128
Reply from 172.17.0.21: bytes=32 time=6ms TTL=128
Reply from 172.17.0.21: bytes=32 time=7ms TTL=128
Reply from 172.17.0.21: bytes=32 time=7ms TTL=128
 
Ping statistics for 172.17.0.21:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 3ms, Maximum = 7ms, Average = 5ms
 
C:\>ping 172.17.30.23
 
Pinging 172.17.30.23 with 32 bytes of data:
 
Request timed out.
Reply from 172.17.30.23: bytes=32 time<1ms TTL=127
Reply from 172.17.30.23: bytes=32 time<1ms TTL=127
Reply from 172.17.30.23: bytes=32 time<1ms TTL=127
 
Ping statistics for 172.17.30.23:
Packets: Sent = 4, Received = 3, Lost = 1 (25% loss),
Approximate round trip times in milli-seconds:
Minimum = 0ms, Maximum = 0ms, Average = 0ms